Hjelp meg å velge

White marks where parts were cut

Usually: Usually a one-bite flush cut. Cut twice: first a few mm out, then close with a thin or single-blade nipper; shave and sand #400 → #1500.

• NightWorks NW-MP02 Ultra-Tynn Enkeltkant Nipper5,100 krAdd to cart
• Pennetype Trimmeskniv For Gundam Og Skala Modellering3,200 krAdd to cart
• Hobby Mio HMD dobbeltsidige slipestikkerfrom 1,500 krOptions

Seams that keep coming back

Usually: Filler shrinks if you sand it before it cures. Fill, wait the full cure, sand, then prime to check. Tinted CA shows exactly what is left.

• DSPIAE Oppgradert Farget Gap Fylling CAfrom 1,900 krOptions
• UStar Justerbar Trinn Sømskraper3,300 krAdd to cart
• 20g Hurtigtørkende Svart/Hvit/Grå Kitt2,100 krOptions
• 10/20/100stk Slipe Kampestikkerfrom 1,100 krOptions

Decals silvering

Usually: Air trapped under the film on matt paint. Gloss coat first; press the water out from the centre. A softening brush helps on curves.

• Hobby Mio 50ml Ferdigblandede Lakk2,400 krOptions
• Plamokojo PMKJ044 Asymmetrisk Dekalpinsett3,200 krAdd to cart
• Galaxy 4-delt sett med vannoverføringspennapplikatorer2,200 krAdd to cart

Paint lifting with the tape

Usually: Grease or mould release under the paint, or tape too sticky. Wash parts before priming; use low-tack tape and pull it back on itself.

• 2~12mm Lavt Tak Fleksibel Maskeringstapefrom 2,200 krOptions
• Hobby Design Ultra-Tynn Modellering Maskeringstape1,700 krOptions

Paint bleeding under masking

Usually: Edges not burnished, or tape too stiff for the curve. Thin flexible tape on curves; burnish the edge with a toothpick.

• 2~10mm Fleksibel Maskeringstapefrom 2,000 krOptions
• Fin linje maskeringstape for skala modelleringfrom 1,800 krOptions

Fogged clear parts

Usually: CA vapour. Glue clear parts with UV glue in small amounts, and let the joint air.

• DSPIAE UV Limfrom 3,700 krOptions
• Flytende/Gel Raskt-herdende UV Limfrom 1,500 krOptions

Airbrush spitting

Usually: Paint too thick, a dirty or bent needle tip, or pressure too low for the mix. Thin a little, clean the tip, raise pressure in small steps.

• Profesjonell Airbrush Rengjøringssett3,100 krAdd to cart
• Airbrush Rengjøringsflaskefrom 1,900 krOptions

Dust in the varnish

Usually: Spraying in a dusty room or touching too soon. Spray booth, clean air, a tack-free wait before handling.

• Bærbar Airbrush Spray Booth for Skala Modeller, Gunpla og Miniatyrer6,900 krAdd to cart
• Stedi MS-86 Antistatisk Støvkostfrom 2,600 krOptions
• Luftstøvsuger og Myk Pensel For Modellrengjøring2,400 krOptions

Wash staining the paint

Usually: Wash on matt or unsealed paint. Seal with satin or gloss first; remove excess with a barely damp brush.

• NightWorks akryllakk og hardlakkfrom 2,800 krOptions
• Hobby Mio 50ml Ferdigblandede Lakk2,400 krOptions
• UStar Panel Line Applicator2,100 krAdd to cart

Grass that looks like carpet

Usually: One colour, one length, lying flat. Mix two lengths and colours; a static applicator stands them up.

• 2mm Statisk Gress Pulver (flere farger)from 2,800 krOptions
• 125ml/flaske 10-13mm lang statisk gress2,600 krOptions
• Cormake statisk gressapplikator og tuftsplaterfrom 2,000 krOptions

Mould lines on miniatures

Usually: Scrape along the line with a scraper at a low angle, then smooth; check under raking light before priming.

• Mo Shi Tools Dobbelhode Skraper og Reamer2,600 krAdd to cart
• UStar Smale Flate Poleringsfilerfrom 2,900 krOptions
• 10/20/100stk Slipe Kampestikkerfrom 1,100 krOptions

Sticky resin print

Usually: Under-washed or under-cured. Gloves on, re-wash, cure as the resin maker says; never sand tacky resin.